 |
Analyze the Steel Type Coal Ball Grinding Mill Faults |
|
Submitted by ballmill
| RSS Feed
| Add Comment
| Bookmark Me!
1. The little pineapple snaggletooth
In the daily use of Ball Mill, the little pineapple snaggletooth happens most often, the reasons are as follows:
(1). The little pineapple design strength is weak, and the manufacturing quality requirements is relatively low.
(2). The lubricating of the little pineapple is bad, the mesh is bad which lead to localized wear, bubbling, and material quality coming off. The local stress concentration is worsened which speed up the snaggletooth.
(3). Supercharge caused by the too many steel balls added into the Coal Ball Mill in production primary which lead to the coal ball mill electric current reaches to 130A. Decrease the steel ball loading capacity, keeping the current at around 120A. (the current raises 1A with one ton steel ball added,)
2. The little pineapple tooth surface abrasion
The gear wheel surface generally presents bubbling, peeling, scallops, and such corrosive pitting phenomenon. Besides the little pineapple tooth surface temperature is high which makes the coal grinding ball mill gear teeth attrition condition seriously.
The reasons are as follows:
(1). The coal grinding ball mill protection cover sealing is not good. There is no sealing on the association point of activity and inertia between the Coal Mill hollow shaft and shelter which speed up the ash entering to the big pineapple. The preheater of the boiler is the three branch warehouse, with one way the secondary air of the blower, one way the primary air of the primary air fan. As the primary air pressure is over-high, it blows down the ash accumulated from the smoke side carrying by the preheater heating surface and takes it away. The pipeline weld bond of the hot air system is unqualified which leads to serious leakage. The ash then enters to the wheel gear shield and speed up its attrition.
(2) The alignment pin problem: It is regulated that the temperature difference measured along the little cutter teeth width should be no more than 8??, and the highest temperature on the tooth surface should be no more than 100??. Hit the alignment pin in after the intervals between each part is normal. When the temperature difference is more than 8??, raise the bearing end of low temperature. One of the reasons for the ball mill tooth surface attrition is that the alignment pin is not hit due to the great work amount which is also the reason why some individual little cutter teeth surface is high and the two ends temperature difference is relatively large.
It consists of motor, reducer, case, milling device, separator, outlet, coal feeding pipe, loading device, control box and sealing apparatus. The fittings are all of superior performance in the world at present. We ensure good quality and durability of the whole machine.
1) The concrete base weight required is only 3 times of that of other similar machines thus the construction expenses is greatly reduced
2) Small vibration while using and doesn't need shock-absorbing device
3) Large load adjustment scope, so it can run under various environments
4) Can bear very strong explosion pressure
5) The grinding roller adopts new material and new craft, which ensures long service life and low maintenance cost
6) There is gap between the grinding parts; it can start with load or offload. Get ball mill,ball mill,rotary kiln From http://www.ballmill8.com
1. The little pineapple snaggletooth
In the daily use of Ball Mill, the little pineapple snaggletooth happens most often, the reasons are as follows:
(1). The little pineapple design strength is weak, and the manufacturing quality requirements is relatively low.
(2). The lubricating of the little pineapple is bad, the mesh is bad which lead to localized wear, bubbling, and material quality coming off. The local stress concentration is worsened which speed up the snaggletooth.
(3). Supercharge caused by the too many steel balls added into the Coal Ball Mill in production primary which lead to the coal ball mill electric current reaches to 130A. Decrease the steel ball loading capacity, keeping the current at around 120A. (the current raises 1A with one ton steel ball added,)
2. The little pineapple tooth surface abrasion
The gear wheel surface generally presents bubbling, peeling, scallops, and such corrosive pitting phenomenon. Besides the little pineapple tooth surface temperature is high which makes the coal grinding ball mill gear teeth attrition condition seriously.
The reasons are as follows:
(1). The coal grinding ball mill protection cover sealing is not good. There is no sealing on the association point of activity and inertia between the Coal Mill hollow shaft and shelter which speed up the ash entering to the big pineapple. The preheater of the boiler is the three branch warehouse, with one way the secondary air of the blower, one way the primary air of the primary air fan. As the primary air pressure is over-high, it blows down the ash accumulated from the smoke side carrying by the preheater heating surface and takes it away. The pipeline weld bond of the hot air system is unqualified which leads to serious leakage. The ash then enters to the wheel gear shield and speed up its attrition.
(2) The alignment pin problem: It is regulated that the temperature difference measured along the little cutter teeth width should be no more than 8??, and the highest temperature on the tooth surface should be no more than 100??. Hit the alignment pin in after the intervals between each part is normal. When the temperature difference is more than 8??, raise the bearing end of low temperature. One of the reasons for the ball mill tooth surface attrition is that the alignment pin is not hit due to the great work amount which is also the reason why some individual little cutter teeth surface is high and the two ends temperature difference is relatively large.
It consists of motor, reducer, case, milling device, separator, outlet, coal feeding pipe, loading device, control box and sealing apparatus. The fittings are all of superior performance in the world at present. We ensure good quality and durability of the whole machine.
1) The concrete base weight required is only 3 times of that of other similar machines thus the construction expenses is greatly reduced
2) Small vibration while using and doesn't need shock-absorbing device
3) Large load adjustment scope, so it can run under various environments
4) Can bear very strong explosion pressure
5) The grinding roller adopts new material and new craft, which ensures long service life and low maintenance cost
6) There is gap between the grinding parts; it can start with load or offload. Get ball mill,ball mill,rotary kiln From http://www.ballmill8.com
Click for Details --> http://www.ballmill8.com <--
|
|
|
|
|
LinkedIn Recommendation:
 Lois Livingston - php Developer at Paratsee - I'm working with Teo on learning new Internet Marketing tips and tricks for my business. He's got a great grasp of just what I need to know, is really fun to work with and although I don't really like to talk on the phone, Teo makes phone conferences really worth the time. I get stuff out of those that aren't anywhere else on his eWorkshopCourses.com site, or the IBC site. If you are looking for a real GURU, Teo is that guy! - March 17, 2012, Lois was Teo's client |
|
Featured [ball mill] Articles:
|
|
