 |
The effect of Ball Mill Charge Pressure and Impact on Grinding |
|
Submitted by ballmill
| RSS Feed
| Add Comment
| Bookmark Me!
The Ball Mill is made up of feeding part, discharging part, gyre part, transmission part(inclding decelerator, small transmission gear, generator, electrical control) and so on. The hollow axis adopts the cast steel and the lining can be replaced, the rotary big gear is processed from cast rolling gear. The barrel body is wearable well and bears wearable scaleboard. So this machine runs steadily and works reliably.
The actual comminution of the material is as result of the pressure exerted by the grinding media and the impact generated by the weight and movement of the charge.
At every phase of grinding operations, there should be a balance between the comminution resulting from pressure and that resulting from impact.
In primary mills, large particles of feed material are crushed by impact. A minimum size of grinding body is needed to generate the required impact. However, this means that a small number of large grinding bodies occupy a large proportion of mill volume. The degree of medium and fine grinding is reduced, and mill throughput is low.
Smaller grinding bodies can be used if their kinetic energy can be increased through greater drop height. This can be achieved by installing higher lifter bars, as shown in figs. E65 and G65.
A comparison of these two pictures shows that the grinding bodies drop off the lifter bars at a greater height in Fig. G65, in which the toe of the charge is also thinner. This indicates that total droop height has increased and that impact force is consequently greater.
The pressure within the charge is very uniform in both cases. Figs. F65, F75 and F85 illustrate how charge pressure decreases as mill speed is increased.
The quantity of grinding bodies is identical in each of these illustrations, although the charge level appears to be higher in F85.
The liner plate profile affects the relative movement of the grinding bodies. This in turn is another important factor with respect to the utilization of mill capacity. Get beneficiation,Mineral Processing,rotary kiln From http://www.ballmill8.com
The Ball Mill is made up of feeding part, discharging part, gyre part, transmission part(inclding decelerator, small transmission gear, generator, electrical control) and so on. The hollow axis adopts the cast steel and the lining can be replaced, the rotary big gear is processed from cast rolling gear. The barrel body is wearable well and bears wearable scaleboard. So this machine runs steadily and works reliably.
The actual comminution of the material is as result of the pressure exerted by the grinding media and the impact generated by the weight and movement of the charge.
At every phase of grinding operations, there should be a balance between the comminution resulting from pressure and that resulting from impact.
In primary mills, large particles of feed material are crushed by impact. A minimum size of grinding body is needed to generate the required impact. However, this means that a small number of large grinding bodies occupy a large proportion of mill volume. The degree of medium and fine grinding is reduced, and mill throughput is low.
Smaller grinding bodies can be used if their kinetic energy can be increased through greater drop height. This can be achieved by installing higher lifter bars, as shown in figs. E65 and G65.
A comparison of these two pictures shows that the grinding bodies drop off the lifter bars at a greater height in Fig. G65, in which the toe of the charge is also thinner. This indicates that total droop height has increased and that impact force is consequently greater.
The pressure within the charge is very uniform in both cases. Figs. F65, F75 and F85 illustrate how charge pressure decreases as mill speed is increased.
The quantity of grinding bodies is identical in each of these illustrations, although the charge level appears to be higher in F85.
The liner plate profile affects the relative movement of the grinding bodies. This in turn is another important factor with respect to the utilization of mill capacity. Get beneficiation,Mineral Processing,rotary kiln From http://www.ballmill8.com
|
|
|
|
|
LinkedIn Recommendation:
 Harold Ramsey - Php Developer at Euromerica USA - Man... I was lost on my business plan until I met Teo through his eWorkshopCourses.com program. He came up with several completely new revenue models for my business that I totally missed! This guy is a powerhouse too with information distribution on the web... When it comes to tech, his firm is a one stop shop! - March 15, 2012, Harold was Teo's client |
|
Featured [beneficiation] Articles:
|
|
