 |
What Industrial Grinding Plant Is? |
|
Submitted by ballmill
| RSS Feed
| Add Comment
| Bookmark Me!
ndustrial Grinding Equipment, often shortened to grinder, is a machine tool used for grinding, which is a type of machining using an abrasive wheel as the cutting tool. Each grain of abrasive on the wheel's surface cuts a small chip from the workpiece via shear deformation.
Introduction
This industrial grinding plant is widely used in dry way powder process of metallic and nonmetallic minerals, and powder size can be adjusted between 30 mesh and 2000 mesh. The processed ores include limestone, calcite, marble, kaolin, gypsum, barite, coal ash, slag, silicon carbide, brown alumina, cement, quartz, feldspar, refractory, etc.
Reasons for grinding:
1.The material is too hard to be machined economically. (The material may have been hardened in order to produce a low-wear finish, such as that in a bearing raceway.)
2.Tolerances required preclude machining. Grinding can produce flatness tolerances of less than ±0.0025 mm (±0.0001 in) on a 127 x 127 mm (5 x 5 in) steel surface if the surface is adequately supported.
3.Machining removes excessive material.
Working principle:
Raw materials are elevated by Bucket Elevator to Ball Mill for being ground. Materials ground by Ball Mill are sent to Classifier for being separated, so the coarse powder and fine powder are separated. Fine powder with suitable size is collected by cyclone collector, coarse powder is discharged from bottom part of Classifier and sent back by Returning Spiral to Ball Mill for being re-ground, this is a closed cycle, the air is discharged by Blower after being cleaned by Pulse Dust Collector.
Features:
1. The industrial grinding plant is stable and highly automatic;
2. Inner lining and grinding media can be changed according to customers’ request, such as high manganese steel, silica, ceramics, etc.
3. Fine powder size is even and can be adjusted;
4. The system is low trouble rate, and can be operated continuously. Get Mineral Processing,rotary kiln,ball mill From http://www.ballmill8.com
ndustrial Grinding Equipment, often shortened to grinder, is a machine tool used for grinding, which is a type of machining using an abrasive wheel as the cutting tool. Each grain of abrasive on the wheel's surface cuts a small chip from the workpiece via shear deformation.
Introduction
This industrial grinding plant is widely used in dry way powder process of metallic and nonmetallic minerals, and powder size can be adjusted between 30 mesh and 2000 mesh. The processed ores include limestone, calcite, marble, kaolin, gypsum, barite, coal ash, slag, silicon carbide, brown alumina, cement, quartz, feldspar, refractory, etc.
Reasons for grinding:
1.The material is too hard to be machined economically. (The material may have been hardened in order to produce a low-wear finish, such as that in a bearing raceway.)
2.Tolerances required preclude machining. Grinding can produce flatness tolerances of less than ±0.0025 mm (±0.0001 in) on a 127 x 127 mm (5 x 5 in) steel surface if the surface is adequately supported.
3.Machining removes excessive material.
Working principle:
Raw materials are elevated by Bucket Elevator to Ball Mill for being ground. Materials ground by Ball Mill are sent to Classifier for being separated, so the coarse powder and fine powder are separated. Fine powder with suitable size is collected by cyclone collector, coarse powder is discharged from bottom part of Classifier and sent back by Returning Spiral to Ball Mill for being re-ground, this is a closed cycle, the air is discharged by Blower after being cleaned by Pulse Dust Collector.
Features:
1. The industrial grinding plant is stable and highly automatic;
2. Inner lining and grinding media can be changed according to customers’ request, such as high manganese steel, silica, ceramics, etc.
3. Fine powder size is even and can be adjusted;
4. The system is low trouble rate, and can be operated continuously. Get Mineral Processing,rotary kiln,ball mill From http://www.ballmill8.com
Click for Details --> http://www.ballmill8.com <--
|
|
|
|
|
LinkedIn Recommendation:
 Lana Cicen - Project Coordinator at The Hope Financial Services, Inc - I had Teo help with my non-tech project I was working, which was a triage system for a construction company - all paper. Teo made it work more efficiently and explained how the new system could be upgraded into a computer program, which included inventory management online. I love this guy! Always one step ahead. I just hired him again make this our phase 2 project. If you are looking for a process guy, Teo is it! - March 17, 2012, Lana was Teo's client |
|
Featured [Mineral Processing] Articles:
|
|
